![Jean B](/img/default-banner.jpg)
- Видео 28
- Просмотров 4 252 595
Jean B
Добавлен 21 дек 2008
Видео
Cheap Backup power Hack for Load Shedding/Rolling Blackouts!
Просмотров 12 тыс.Год назад
Cheap mod of a PC UPS will give you hours of backup power if your home's power gets cut. I used a 45ah car battery for 2 years and it would keep my wifi and LED bulb burning for 5hours. I received this 100ah battery in the video for free,so will definitely be using it. Any battery between 45ah and 100ah should work.
Auction Salvaged PS3 Repair
Просмотров 4742 года назад
I buy two PS3 slims on an auction and try and repair them. One unit goes on then off almost immediately. The other cannot read the hard drive. Trying to make my money back as this is something I like doing and will keep doing as long as I don't have to spend more money than I make!
Pool Pump only Humming (not running)
Просмотров 55 тыс.2 года назад
Hi All. This video shows you the steps to follow if you have a pool pump that is only humming and does not want to turn or pump water. Most of the time this is an easy fix.
How Much Copper From Scrap Ballast???
Просмотров 4,4 тыс.2 года назад
I got 12 scrap ballasts from a site I worked at and decided to see how much copper and metal I can scrap from it. Results are at the end.
How to connect a trailer plug if you don't know the wire colors
Просмотров 146 тыс.2 года назад
An easy way to connect a trailer plug if you don't know the wire colors.
Connecting a 3 phase motor with 1 phase Power with Diagram
Просмотров 1,1 млн4 года назад
If you only have single phase power at your house,you can still connect a three phase motor with this tutorial.
Connecting a Dimmer switch to a Bulb
Просмотров 20 тыс.4 года назад
This video will show you how to connect a dimmer module to a switch. This is not for a LED bulb as it uses a special dimmer module.
12Vdc Day/Night (Light) Switch
Просмотров 20 тыс.4 года назад
12Vdc Day/Night Switch. Switching 12Vdc,24Vdc,48Vdc and 230Vac. This switch can be used with 12Vdc solar curcuit. Colour Changing Strip light link ebay - rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&ipn=icep&toolid=20004&campid=5338592260&mpre=https://www.ebay.com/itm/RGB-LED-Color-Changing-Light-Strip-Music-Sound-Activated-Sync-Kit-12V-300-LEDs/123602494621?var=424179059306&_trkparms...
How to Diagnose and Repair a Hot Water Cylinder/Geyser
Просмотров 92 тыс.4 года назад
How to Diagnose and Repair a Hot Water Cylinder/Geyser
How to Wire a Distribution Board
Просмотров 170 тыс.5 лет назад
This video will show you how to connect/wire a home distribution board. This is for rules in South Africa,please check you rules and regulations.
How to Connect a Single Phase Motor
Просмотров 603 тыс.5 лет назад
This video will show you how to connect a Single phase motor with two capacitors. A motor with a start and run capacitor and a start and run coil.
Infra Red Motion Sensor Eurolux C0149
Просмотров 2,3 тыс.5 лет назад
I show you how to connect a Eurolux C0149 Infra Red Motion Sensor.
KiloWatt hour (KWh) meter. Electricity meter.
Просмотров 15 тыс.5 лет назад
How to connect a analog KWh meter.
Phase Failure Phase Reversal/Sequence Relay
Просмотров 30 тыс.5 лет назад
How to connect a Phase Failure Phase Reversal/Sequence Relay with a contactor.
Connecting a National/Waco Universal Timer
Просмотров 19 тыс.5 лет назад
Connecting a National/Waco Universal Timer
Easily change a flourescent tube to LED tube.
Просмотров 71 тыс.5 лет назад
Easily change a flourescent tube to LED tube.
How to Connect a Direct online Starter (DOL Starter)
Просмотров 26 тыс.6 лет назад
How to Connect a Direct online Starter (DOL Starter)
How to Connect a Timer to Your Geyser/Hot Water Cylinder
Просмотров 258 тыс.6 лет назад
How to Connect a Timer to Your Geyser/Hot Water Cylinder
Day/Night (or Light) switching Connecting
Просмотров 630 тыс.6 лет назад
Day/Night (or Light) switching Connecting
How to connect a Normal Light Switch
Просмотров 100 тыс.6 лет назад
How to connect a Normal Light Switch
2 Way Switching (Switch on/off a light from 2 switches)
Просмотров 8 тыс.6 лет назад
2 Way Switching (Switch on/off a light from 2 switches)
Earth Leakage Trip...Here's what to do. (RCD)
Просмотров 314 тыс.10 лет назад
Earth Leakage Trip...Here's what to do. (RCD)
Chevrolet Lumina SS V8 Drifting burnout.qt
Просмотров 57 тыс.12 лет назад
Chevrolet Lumina SS V8 Drifting burnout.qt
Your sound disappeared towards the end
What happens it the earth is making it trip
compleatly wrong
Hi. Please explain why its wrong and we all can learn something.
Can you help me with the PDF
Simple and useful explation and solution to the motor problem.
In the UK, we use a solid copper busbar, for feeding all the MCB's
Nice video indeed how did you earth the third wire please let me know thanks
Hi. Most of the old and new metal fittings have a little tab where a connector slides over and screws onto. It you have a plastic fitting,no earth is needed. If you have a meral one with no earth tab. Drill a hole in the metal and put a nut and bolt through to fasten the earth wite. Groete
Thanks your explanation is clear
For 4kw 5.5hp 50 hz 3 phase motor what size of capacitor should i use? Can you please advise 😊
It's nice and beautiful demonstration, now I got it
Una no de hear word.. .. All these animals wey be food, una say na Pet.. Continue
What the course if the gyser it's new it's get hot after couple hours the water get cold what's the course
Hi. That is a difficult one. Check if the supply is not interrupted by a timer maybe. If you have a tester you can check if the supply voltage is at the element when the water is cold. This could mean an element problem but further testing will be needed...
This absolutely worked it was the fan which was not moving. Removed the cover and spun the fan and removed anything that was there and it worked perfectly. Had not used my motor for over 2 months.
same!!!!!
So helpful thank u
Why bridge
Very comprehensive and detailed expo. Thanks a lot
Thankyou
Now I know! :o)
But u can temp run ur breakers run on ur main breaker 4 ex ur lights breaker feeds from ur main and ur plugs 4rm ur earth leakage u know .
De toute les vidéo Sai bon❤
Fair play got me out of a hole borrowed a trailer when taking it off I forgot to take this out a ripped wires out
I forgot to plug in the plug once, went on to destroy the plug while driving... Happens to the best of us :) Glad the video helped!
@@p0we111 i actually dragged the whole light panel bout 5 miles before too i was hungover thats my excuse lol
@@nigelhoary :) Would have payed money to see that going down the road!
good clip friend
I have the exact same connections and a start and run cap. If I connect it up like you have it will start then slow almost to a stop then start again over and over. If I follow the wiring diagram I found on the net for my motor it's won't start it just struggle to even turn. Motor is YL90L-2. My start cap is 200uf, the run cap is 40uf. U1 and u2 is 1.7 ohms, w1(z1) and w2(z2) is 2.0ohms. V1 and v2 is closed circuit 0 ohms. Its a brand new motor. I also tried another wiring arrangement and it ran to about 30 psi for 2 minutes before it started slowing and then accelerating cycling. I just can't believe there isn't a proper diagram that I can find showing everything the connections the caps where they connect for this motor. The useless diagram just show the terminals and links for cw ccw, no mention where to put the caps. 😢
Where is the centrifugal switch?
Hi. The centrifugal switch is inside the motor around the shaft at the front of the motor usually.
@@p0we111 thanks alot engineer
This is not a three phase motor? But it has 3 windings, so he is running a 3 phase motor with a single phase power supply, not running a single phase motor, corre t me if I'm wrong plz
My motor runs but its not pumping up water. Iv tried to attach the hose to it to prime it, but still not pumping water . My pump is for boar hole to water the garden.
Hi Sandyseale. Difficult to say,but Ive seen some borehole pumps that strip the coupling between the motor and pump fitting. Then the motor turns but no water is pumped. It can also just be the pump side that is damaged internally. If you are sure the motor has enough water to prime it,then you would have to inspect the pump side. Unfortunately that is the only part left if the motor is running
@@p0we111 Thank you
Much appreciated!
Nice work
Thank you for the great video! What if at the time of replacement of LED tube , i swap the ends of the led tube i.e the end with writtings with the end with no writtings, what will happen, kindly?
Hi. The one side that should have no power is shorted. So putting in the wrong way will cause a dead short between Live and Neutral.... Not good 😊
@@p0we111 Thanks
@@p0we111 but why should it just be left open?
@@Le_VisN one side of the LED tube requires Live on one pin and Neutral on the other. The other side has no power and is just there to hang in the existing holders. No power to that one side.
@@p0we111 OK
Thank you, Sir! I just saved 200 bucks for replacing the pump.
how the transformer handles high AC draw? doesn't it heat up fast? would it help to have 2 fans installed to make it safe?
Hi. The AC draw remains the same as you can only use the available watts. 600watts for the smal UPS.
Great Vid. Thanks I take it that an Ac Air conditioner is also wired as a stove geyser lights cct via the Main buzz bar for neutrals and the live feed only from the Main switch?
Hi. Yes you are correct. Just have an isolator next to the aircon.
@@p0we111 Thanks. for the quick response The isolator is for servicing tech to isolate the AC for safe maintenance.
@@SnowyPe No problem. Yes exactly as you say.
A Video of 9 years have help me today, almost went out to buy a new earth leakage… the disconnection of all the neutral wires is what saved me today… I actually found the faulty wire that way… a million thanks… big ups..
Thanks! Much appreciated. Subbed.
Hey just looking for some help.
Bly om te sien jou channel is weer aktief! :-D
Nie so aktief soos julle channel nie :) Ek liaak die nuwe Baviaans reeks!
What of the house as faults and the board did not trip of
Hi Micheal. Im not sure but I think this is your question: If a house has faults but the breakers does not trip,why would that be. It depends on the type of fault. If it has a loose wire then nothing will happen. If the loose wire touches a plastic part,then nothing will happen. If the loose wire touches a metal part and nothing happens then the installation is not correct as the metal part needs to be earthed/grounded.
Thank you this was super helpful
Great video
❤❤❤❤❤❤❤❤❤❤❤❤❤❤
what do you think is the problem when the pump suddenly stops after 2 - 3 minutes? and starts again in about 5 minutes on its own?
Hi. It may be a thermal switch tripping when the motor gets too hot and starting when it cools down. Feel how hot the motor is to the touch. Maybe it does not turn freely....
@@p0we111 Will do, thanks.
That's great. I have been struggling to wire this after watching this video,i found it very simple.
Thanks, very helpfull.
Thanks for this cant u do one for a double switch
Will the contactor turn on really? Because i am not seeing neutral supply connected to any of the contactor coil( A1 or A2). You've only supplied blue phase directly to coil A1 of the contactor and another wire taken from port 3 of phase failure to A2. Where is neutral taken to? I need help plz
Hi. The only reason to put a phase failure/phase reversal relay in your main DB or for pumps is bacause it is 3phase. To connect a neutral wire would mean a single phase connection and it would not be necessary to put a phase failure in a single phase connection as there would be no damage as in 3phase if the one phase drops.
@@p0we111 I'm referring to the contactor, sir. The wiring of phase failure I understood very well. May be I don't understand the concept of contactor in this scenario. Because I have always known that for the contactor to be energized, it must be supplied with phase at A1 and neutral at A2 or vise versa but for this case contactor is supplied with 2 phases
@@Le_VisNHi. Yes you are correct in your observation. A1 is a phase and A2 is a phase. This is a 400vac contactor where the one you speak of with the Neutral is a 230vac contactor.
@@p0we111 ok sir, so in 400vac contactor we connect phase to both A1 and A2?
@@Le_VisN Yes. Connect a different phase to each A1 and A2
Well explained
Hi thank you for the video. Where can I buy the Capacitor. I lives in capetown south africa.
Hi. Try Voltex or ACDC. Groete
I have question, how to wire REVERSE light? Thx
I replaced the rubber gasket a month ago only to find it pushing out water at a high rate again. Interesting 🤔 I switched it off and left it to cool down over two days and it stopped leaking altogether. Could it be the pressure valve perhaps? Not sure how to adjust that? The valve has been dry throughout the process. Any advice would be appreciated 😊
Hi. I would suspect the pressure valave yes. The rubber gasket would leak and continue leaking. Plumbers have told me that some water coming out of the pressure valve is normal,but if it continues ill check with a plumber if I were you. Groete
Thanks, video helped me 👍